All New motoral testpoint Latest
DOWNLOAD
Motorola RAZR V3 repair and housing change guide
Motorola RAZR V3 repair and housing change guide
This guide will step through the process required to repair a Motorola RAZR V3 “the phone”, including the flex cable and then replacing the housing.
The flex cable can be purchased from eBay for $7 US (including shipping), and the housing can be purchased for around $16 (including shipping). The flex cable is attached to the keypad circuit, which is automatically included in the purchase. When purchasing the housing, you need to make sure it is NOT a slip on case, skin, pouch, fascia, protector, etc, etc. The housing should include as a minimum the front, middle, back and battery cover. Keypad, hinge, pads, grommets, buttons may even be included, as well as TORX screwdrivers, make sure you buy all what you need. The included contents of my purchased housing were as follows.
To perform repairs on the phone, you require TORX T5 and T4 drivers, a small flat driver will come in handy as well, also at least 2 hours of spare time.
First a look at my broken phone, besides the obvious fact that it is broken into two separate halves, the hinge is broken and there is normal housing wear.
First remove the battery cover, battery and SIM card. Remove 2 TORX T5 screws under the battery cover circled in red. Separate the plastic case via two plastic clips as squared in red.
The antenna assembly can be removed by disconnection of the keyboard connector, squared in red. Remove the 4 TORX T4 screws, circled in red. These screws will be required for the new housing.
Now, if you need to preserve the keypad circuit; it is a little bit more involved. First, lift up the tabs of the metal keypad as circled in red and then pry of the metal keypad. Most likely the keypad circuit will be stuck to the plastic so extreme care is required when removing. It may be easier to reuse this whole part, as it seems all colour housing still have this same silver part.
Following is a photo of the new keypad circuit and the plastic keyboard housing.
Remove the backing of the keypad circuit and stick the circuit to the plastic housing. You will need to start from the bottom to allow the connectors to be threaded through the holes.
A photo of the completed keypad assembly.
Remove the antenna from the antenna assembly by first removing two black grommets and then unclipping the two plastic clips.
Once the circuit board is removed, remove all the following from the plastic housing as these are required in the new housing.
Insert all the old removed parts into the new housing as follows.
The change the screen housing, first remove the 4 rubber grommets as circled in red, and then the 4 TORX T5 screws behind.
Once the plastic screen housing is removed, the display circuit is visible. Carefully pry away the circuit from the plastic near all buttons and the backup battery as circled in red. The camera can be removed by lifting the brown tab as squared in red. Move the circuitry to the new housing and then connect the camera.
To connect the two clamshell halves, the hinge can be retracted in, the hinge is circled in red. This allows the two halves to combine; the hinge should then pop into place securing the two halves.
Finally, replace all the finishing touches such as labels, hinge caps and grommets. Photos of the new phone are below.
The following repair guide may be of further help
Motorola MILESTONE XT720 - Hard Reset / Factory Data Reset
MILESTONE XT720 - Resetting to factory data fresh default settings.
WARNING: This process will deleted all data stored on your device. However, All data stored on the MicroSD will be affected. Please back first before proceeding.
To Perform a Reset
# Open the Applications Tray. (arrow pointing up located in the middle at the bottom of the display screen)
# Select Settings
# Select Privacy
# Select Factory data reset
# Select Reset Phone
# Select Erase Everything
To Manually Hard Reset
If there are significant problems with your device or you are not able to follow the steps above please use the following process to manually reset the phone:
1. Turn off phone
2. Press Power key + Camera Key to power on the phone and bring up the recovery screen
3. PressVolume Up + Camera Key to show the recovery menu.
4. SelectWipe data/factory reset
5. Select Reboot Phone
Note: Once the phone reboot, all your data and application already deleted on your Motorola MILESTONE XT720, you need to install them back again.
.....:::All in one for Motorola:::.....
RSDLite_v4.4.1
motorola fls backup
P2K_Easy_Tool_v39
MotoRocker_300 crack
Motorola Repair Studio v1.02 Full
Unlock V80-V220-E380-C450-C550-C650
moto_boot_screen reaplacer
Ramldr2.0.34
Handset_USB_Driver_32_v3.7.0
DOWNLOAD
http://rapidshare.com/files/164249673/All_in_one_for_motorola.exe
Motorola v220 speaker problem solutions
when you deal damage your speakers, or speakers do not work properly on motorola v200, of course you would replace with a new one, this is already experienced by some engineers in Indonesia, but still does not work, before replacing with a new one, it's worth a check first line of speakers, because in my experience it rarely happens speakers die, but I've proven if facing speakers on motorola v220 damage, which often occurs only damage to the lane, or line break
How to repair not charging motorola v8
some trick had been done to repair charge motorola experiencing problems, in this case I will discuss the problem of charging the Motorola V8, which can not be charging,
not charging motorola v8, could be due to several components that have been damaged, due to too long when charging, and we certainly think this should do the replacement of spare parts, tap the main obstacle is the difficult part spart we get in the shops nearby.
you need not worry that by doing our jumpers can want to know how to do it? please see picture
Subscribe to:
Posts (Atom)
Chinese
French
German
Italian
Japanese
Korean
Russian
Spanish
